View AFK475M50B12T_4092794.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.020 cornell dubilier your source for capacitor solutions chip and smt capacitors type afk, -55 c to 105 c smt aluminum electrolytic capacitors - lowest e.s.r., 105 c lowest esr and long life for filtering, bypassing, power supply decoupling highlights ? +105 c, up to 5000 hour load life ? capacitance range: 3.3 f to 6800 f ? voltage range: 6.3 vdc to 100 vdc specifications operating temperature: rated voltage: capacitance: capacitance tolerance: leakage current: ripple current multiplier: dissipation factor: -55 c to +105 c 6.3, 10, 16, 25, 35, 50, 63, 80 & 100 vdc 3.3 f to 6800 f 20% @ 120 hz and +20 c 0.01 cv or 3 a @ +20 c, after two minutes (whichever is greater) frequency life test: shelf life: 2000 h @ +105 c, 4.0 - 10.0 mm dia. 5000 h @ +105 c, 12.5 - 18.0 mm dia. ? capacitance 30% df: 200% of limit dcl: 100% of limit 1000 h @ +105 c ? capacitance 30% df: 200% of limit dcl: 100% of limit outline drawing case dimensions series 6.3 v10 v16 v25 v35 v50 v63 v80 v100 v 0.26 0.19 0.16 0.14 0.12 0.1 0.08 0.08 0.07 add 0.02 per 1000 f for values greater than 1000 f afk series marking type afk capacitors are the best and by a wide margin. with 40% to 60% l ower impedance, 30% to 50% smaller case size and more than twice the life compared to low-esr type afc, the type afk also excels at cold performance down to -55 c. in addition, this terrific, low-impedance performance approaching low-esr tantalum capacitors is at a significant cost savings compared to tantalum. the vertical cylindrical cases facilitate automatic mounting and reflow soldering into the same footprint of like-rated tantalum capacitors except without the need for voltage derating. (mm) fk 220 capacitance ( f) v oltage lot no. j6.3vdc a10vdc c16vdc e25vdc v35vdc h50vdc j63vdc k80vdc 2a 100vdc h l w p d 0.3 mm max. a i i k 50/60 hz 120 hz 1 khz 10 khz 100 khz 0.7 0.75 0.9 0.95 1.0 case code d .05 l a 0.2 h (max) i (ref) w p (ref) k b 4.0 5.8 0.3 4.3 5.5 1.8 0.65 0.1 1.0 0.35 +0.15/-0.20 c 5.0 5.8 0.3 5.3 6.5 2.2 0.65 0.1 1.5 0.35 +0.15/-0.20 d 6.3 5.8 0.3 6.6 7.8 2.4 0.65 0.1 1.8 0.35 +0.15/-0.20 x 6.3 7.9 0.3 6.6 7.8 2.4 0.65 0.1 1.8 0.35 +0.15/-0.20 e 8.0 6.2 0.3 8.3 9.5 3.4 0.65 0.1 2.2 0.35 +0.15/-0.20 f 8.0 10.2 0.3 8.3 10.0 3.4 0.90 0.3 3.1 0.70 0.20 g 10.0 10.2 0.3 10.3 13.0 3.5 0.90 0.3 4.6 0.70 0.20 h 12.5 13.5 0.5 13.5 15 4.7 0.90 0.3 4.4 0.70 0.30 p 16 16.5 0.5 17 19 5.5 1.2 0.3 6.7 0.70 0.30 r 18 16.5 0.5 19 21 6.7 1.2 0.3 6.7 0.70 0.30
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.021 chip and smt capacitors cornell dubilier your source for capacitor solutions type afk, -55 c to 105 c smt aluminum electrolytic capacitors - lowest e.s.r., 105 c ratings table max. max. max. max. dissipatio n esr @ impedance ripple current cap catalog dcl factor @ 100 khz @ 100 khz @ 105c case size (mm) quantity fnumber a/2 120 hz 20 c 20 c 100 khz code d x l per reel min) 20 c( ? )() (ma) 22 afk226m06b12t 3.0 0.26 1.35 1.35 90 b 4x5.8 2000 47 afk476m06b12t 3.0 0.26 1.35 1.35 90 b 4x5.8 2000 47 afk476m06c12t 3.0 0.26 0.7 0.7 160 c 5x5.8 1000 100 afk107m06c12t 6.3 0.26 0.7 0.7 160 c 5x5.8 1000 100 afk107m06d16t 6.3 0.26 0.36 0.36 240 d 6.3x5.8 1000 220 afk227m06d16t 13.9 0.26 0.36 0.36 240 d 6.3x5.8 1000 330 afk337m06x16t 20.8 0.26 0.34 0.34 280 x 6.3x7.7 900 330 afk337m06e16t 20.8 0.26 0.26 0.26 300 e 8x6.2 1000 470 afk477m06f24t 29.6 0.26 0.16 0.16 600 f 8x10.2 500 1000 afk108m06f24t 63.0 0.26 0.16 0.16 600 f 8x10.2 500 1500 afk158m06g24t 94.5 0.26 0.08 0.08 850 g 10x10.2 500 3300 afk338m06h32t 207.9 0.3 0.06 0.06 1100 h 12.5x13.5 200 6800 afk688m06p44t 428.4 0.36 0.035 0.035 1800 p 16x16.5 125 22 afk226m10b12t 3.0 0.19 1.35 1.35 90 b 4x5.8 2000 33 afk336m10b12t 3.3 0.19 1.35 1.35 90 b 4x5.8 2000 33 afk336m10c12t 3.3 0.19 0.7 0.7 160 c 5x5.8 1000 150 afk157m10d16t 15.0 0.19 0.36 0.36 240 d 6.3x5.8 1000 220 afk227m10x16t 22.0 0.19 0.34 0.34 280 x 6.3x7.7 900 220 afk227m10e16t 22.0 0.19 0.26 0.26 300 e 8x6.2 1000 330 afk337m10f24t 33.0 0.19 0.16 0.16 600 f 8x10.2 500 470 afk477m10f24t 47.0 0.19 0.16 0.16 600 f 8x10.2 500 1000 afk108m10g24t 100.0 0.19 0.08 0.08 850 g 10x10.2 500 2200 afk228m10h32t 220.0 0.21 0.06 0.06 1100 h 12.5x13.5 200 4700 afk478m10p44t 470.0 0.25 0.035 0.035 1800 p 16x16.5 125 6800 afk688m10r44t 680.0 0.29 0.033 0.033 2060 r 18x16.5 125 10 afk106m16b12t 3.0 0.16 1.35 1.35 90 b 4x5.8 2000 22 afk226m16b12t 3.5 0.16 1.35 1.35 90 b 4x5.8 2000 22 afk226m16c12t 3.5 0.16 0.7 0.7 160 c 5x5.8 1000 47 afk476m16c12t 7.5 0.16 0.7 0.7 160 c 5x5.8 1000 47 afk476m16d16t 7.5 0.16 0.36 0.36 240 d 6.3x5.8 1000 68 afk686m16d16t 10.9 0.19 0.36 0.36 240 d 6.3x5.8 1000 100 afk107m16d16t 16.0 0.16 0.36 0.36 240 d 6.3x5.8 1000 150 afk157m16x16t 24.0 0.16 0.34 0.34 280 x 6.3x7.7 900 220 afk227m16x16t 35.2 0.16 0.34 0.34 280 x 6.3x7.7 900 220 afk227m16e16t 35.2 0.16 0.26 0.26 300 e 8x6.2 1000 330 afk337m16f24t 52.8 0.16 0.16 0.16 600 f 8x10.2 500 470 afk477m16f24t 75.2 0.16 0.08 0.08 850 f 8x10.2 500 680 afk687m16g24t 108.8 0.16 0.08 0.08 850 g 10x10.2 500 1500 afk158m16h32t 240 0.16 0.06 0.06 1100 h 12.5x13.5 200 3300 afk338m16p44t 528 0.2 0.035 0.035 1800 p 16x16.5 125 4700 afk478m16r44t 752 0.22 0.033 0.033 2060 r 18x16.5 125 10 afk106m25b12t 3.0 0.14 1.35 1.35 90 b 4x5.8 2000 22 afk226m25c12t 5.5 0.14 0.7 0.7 160 c 5x5.8 1000 33 afk336m25c12t 8.3 0.14 0.7 0.7 160 c 5x5.8 1000 33 afk336m25d16t 8.3 0.14 0.36 0.36 240 d 6.3x5.8 1000 47 afk476m25d16t 11.8 0.14 0.36 0.36 240 d 6.3x5.8 1000 68 afk686m25d16t 17.0 0.14 0.36 0.36 240 d 6.3x5.8 1000 100 afk107m25x16t 25.0 0.14 0.34 0.34 280 x 6.3x7.7 900 100 afk107m25e16t 25.0 0.14 0.26 0.26 300 e 8x6.2 1000 150 afk157m25f24t 37.5 0.14 0.16 0.16 600 f 8x10.2 500 220 afk227m25f24t 55.0 0.14 0.16 0.16 600 f 8x10.2 500 330 afk337m25f24t 82.5 0.14 0.16 0.16 600 f 8x10.2 500 470 afk477m25g24t 117.5 0.14 0.16 0.16 850 g 10x10.2 500 1000 afk108m25h32t 250 0.14 0.06 0.06 1100 h 12.5x13.5 200 2200 afk228m25p44t 550 0.16 0.035 0.035 1800 p 16x16.5 125 3300 afk338m25r44t 825 0.18 0.033 0.033 2060 r 18x16.5 125 6.3 vdc ( 8 vdc surge) 10 vdc (13 vdc surge) 16 vdc ( 20vdc surge) 25 vdc ( 31 vdc surge)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.022 cornell dubilier your source for capacitor solutions chip and smt capacitors part numbering system type afk, -55 c to 105 c afk type 106 capacitance m capacitance tolerance voltage code 16 b case code 12t packaging code 105 = 1.0 f 106 = 10 f 107 = 100 f 108 = 1000 f m = 20% 12 = carrier tape width (mm) t = tape & reel b = bulk 06 = 6.3 vdc 10 = 10 vdc 16 = 16 vdc 25 = 25 vdc 35 = 35 vdc 50 = 50 vdc 63 = 63 vdc 80 = 80 vdc 2a = 100 vdc smt aluminum electrolytic capacitors - lowest e.s.r., 105 c ratings table max. max. max. max. dissipation esr @ impedance ripple current cap catalog dcl factor @ 100 khz @ 100 khz @ 105 c case size (mm ) quantity f num ber ( a/2 120 hz 20 c 20 c 100 khz code d x l per reel m in) 20 ? ? ma) 4.7 afk475m 35b12t 3.0 0.12 1.35 1.35 90 b 4x5.8 2000 10 afk106m 35b12t 3.5 0.12 1.35 1.35 90 b 4x5.8 2000 10 afk106m 35c12t 3.5 0.12 0.7 0.7 160 c 5x5.8 1000 22 afk226m 35c12t 7.7 0.12 0.7 0.7 160 c 5x5.8 1000 33 afk336m 35d16t 11.6 0.12 0.36 0.36 240 d 6.3x5.8 1000 47 afk476m 35d16t 16.5 0.12 0.36 0.36 240 d 6.3x5.8 1000 68 afk686m 35x16t 23.8 0.12 0.34 0.34 280 x 6.3x7.7 900 100 afk107m 35x16t 35.0 0.12 0.34 0.34 280 x 6.3x7.7 900 100 afk107m 35f24t 35.0 0.12 0.16 0.16 600 f 8x10.2 500 150 afk157m 35f24t 52.5 0.12 0.16 0.16 600 f 8x10.2 500 220 afk227m 35f24t 77.0 0.12 0.16 0.16 600 f 8x10.2 500 330 afk337m 35g24t 115.5 0.12 0.08 0.08 850 g 10x10.2 500 470 afk477m 35h32t 164.5 0.12 0.06 0.06 1100 h 12.5x13.5 200 680 afk687m 35h32t 238 0.12 0.06 0.06 1100 h 12.5x13.5 200 1500 afk158m 35p44t 525 0.12 0.035 0.035 1800 p 16x16.5 125 4.7 afk475m 50b12t 2.4 0.10 2.9 2.9 60 b 4x5.8 2000 10 afk106m 50c12t 5.0 0.10 1.52 1.52 85 c 5x5.8 1000 10 afk106m 50d16t 5.0 0.10 0.88 0.88 165 d 6.3x5.8 1000 22 afk226m 50d16t 11.0 0.10 0.88 0.88 165 d 6.3x5.8 1000 33 afk336m 50x16t 16.5 0.10 0.68 0.68 195 x 6.3x7.7 900 33 afk336m 50e16t 16.5 0.10 0.68 0.68 195 e 8x6.2 1000 47 afk476m 50x16t 23.5 0.10 0.68 0.68 195 x 6.3x7.7 900 47 afk476m 50e16t 23.5 0.10 0.68 0.68 195 e 8x6.2 1000 100 afk107m 50f24t 50.0 0.10 0.34 0.34 350 f 8x10.2 500 150 afk157m 50g24t 75.0 0.10 0.18 0.18 670 g 10x10.2 500 220 afk227m 50g24t 110 0.10 0.18 0.18 670 g 10x10.2 500 330 afk337m 50h32t 165 0.10 0.12 0.12 900 h 12.5x13.5 200 680 afk687m 50p44t 340 0.10 0.073 0.073 1610 p 16x16.5 125 1000 afk108m 50p44t 500 0.10 0.073 0.073 1610 p 16x16.5 125 4.7 afk475m 63c12t 2.96 0.08 3 3 50 c 5x5.8 1000 10 afk106m 63d16t 6.3 0.08 1.5 1.5 80 d 6.3x5.8 1000 22 afk226m 63x16t 13.9 0.08 1.2 1.2 120 x 6.3x7.7 900 22 afk226m 63e16t 13.9 0.08 1.2 1.2 120 e 8x6.2 1000 33 afk336m 63f24t 20.8 0.08 0.65 0.65 250 f 8x10.2 500 47 afk476m 63f24t 29.6 0.08 0.65 0.65 250 f 8x10.2 500 68 afk686m 63g24t 42.8 0.08 0.35 0.35 400 g 10x10.2 500 100 afk107m 63g24t 63.0 0.08 0.35 0.35 400 g 10x10.2 500 150 afk157m 63h32t 94.5 0.08 0.35 0.35 800 h 12.5x13.5 200 220 afk227m 63h32t 138.6 0.08 0.16 0.16 800 h 12.5x13.5 200 470 afk477m 63p44t 296.1 0.08 0.082 0.082 1410 p 16x16.5 125 680 afk687m 63r44t 428.4 0.08 0.08 0.08 1690 r 18x16.5 125 3.3 afk335m 80c12t 2.64 0.08 5 5 25 c 5x5.8 1000 4.7 afk475m 80d16t 3.76 0.08 3 3 40 d 6.3x5.8 1000 10 afk106m 80x16t 8.0 0.08 2.4 2.4 60 x 6.3x7.7 900 10 afk106m 80e16t 8.0 0.08 2.4 2.4 60 e 8x6.2 1000 22 afk226m 80f24t 17.6 0.08 1.3 1.3 130 f 8x10.2 500 33 afk336m 80f24t 26.4 0.08 1.3 1.3 130 f 8x10.2 500 47 afk476m 80g24t 37.6 0.08 0.7 0.7 200 g 10x10.2 500 68 afk686m 80h32t 54.4 0.08 0.32 0.32 500 h 12.5x13.5 200 100 afk107m 80h32t 80.0 0.08 0.32 0.32 500 h 12.5x13.5 200 150 afk157m 80h32t 120 0.08 0.32 0.32 500 h 12.5x13.5 200 330 afk337m 80p44t 264 0.08 0.17 0.17 793 p 16x16.5 125 470 afk477m 80r44t 376 0.08 0.153 0.153 917 r 18x16.5 125 22 afk226m 2af24t 22.0 0.07 1.3 1.3 130 f 8x10.2 500 33 afk336m 2ag24t 33.0 0.07 0.7 0.7 200 g 10x10.2 500 47 afk476m 2ah32t 47.0 0.07 0.32 0.32 500 h 12.5x13.5 200 68 afk686m 2ah32t 68.0 0.07 0.32 0.32 500 h 12.5x13.5 200 100 afk107m 2ap44t 100 0.07 0.17 0.17 793 p 16x16.5 125 150 afk157m 2ap44t 150 0.07 0.17 0.17 793 p 16x16.5 125 220 afk227m 2ar44t 220 0.07 0.153 0.153 917 r 18x16.5 125 330 afk337m 2ar44t 330 0.07 0.153 0.153 917 r 18x16.5 125 100 vdc (125 vdc surge) 35 vdc (44 vdc surge ) 50 vdc (63 vdc surge ) 63 vdc (75 vdc surge ) 80 vdc (100 vdc surge)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.023 chip and smt capacitors cornell dubilier your source for capacitor solutions type afk, -55 c to 105 c typical performance curves smt aluminum electrolytic capacitors - lowest e.s.r., 105 c 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value 65 c 25 c 85 c 0 c ? 40 c 45 ? 20 105 ? 55 c . 0.01 0.1 1 10 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c 0 c 25 c 65 c85 c 45 c ? 20 c 105 c ? 55 c 0.1 1 10 100 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c ? 20 c 0 c 25 c 45 c 85 c 65 c 105 ? 55 c 0 0.2 0.4 0.6 0.8 1 1.2 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value 65 c 25 c 85 c 0 c 105 c ? 40 c 45 ? 20 c ? 55 c 0.001 0.01 0.1 1 10 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c 0 c 25 c 65 c 85 c 45 c ? 20 c 105 c ? 55 c 0.1 1 10 100 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c ? 20 c 0 c 25 c 45 c 85 c 65 c 105 c ? 55 c impedance vs. temperature and frequency impedance vs. temperature and frequency esr vs. temperature and frequency esr vs. temperature and frequency 100 f @ 16 vdc (6.3 x 5.8 mm) capacitance vs. temperature & frequency capacitance vs. temperature & frequency 100 f @ 16 vdc (6.3 x 5.8 mm) 100 f @ 16 vdc (6.3 x 5.8 mm) 3300 f @ 6.3 vdc (12.5 x 13.5 mm) 3300 f @6.3 vdc (12.5 x 13.5 mm) 3300 f @6.3 vdc (12.5 x 13.5 mm) frequency (hz) frequency (hz) frequency (hz) frequency (hz) frequency (hz) frequency (hz)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.024 cornell dubilier your source for capacitor solutions chip and smt capacitors type afk, -55 c to 105 c typical performance curves smt aluminum electrolytic capacitors - lowest e.s.r., 105 c 0 1 2 3 -60 -10 40 90 140 d.f. (@ 120 hz) 47 f @ 6.3 vdc (4 x 5.8 mm) 100 f @ 6.3 vdc (6.3 x 5.8 mm) 1000 f @ 6.3 vdc (8 x 10.2 mm) -2 0 -1 5 -1 0 -5 0 5 0 500 1000 1500 2000 2500 3000 3500 capacitance change (%) 22 f @ 6.3 vdc (4 x 5.4 mm) 100 f @ 6.3 vdc ( 6.3 x 5.4 mm) 1500 f @ 6.3 vdc (10 x 10.2 mm) 0 0.2 0.4 0.6 0.8 1 1.2 1.4 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value 65 c 25 c 85 c 0 c ? 40 c 45 c ? 20 c 105 c ? 55 c 0.1 1 10 100 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c ? 20 c 0 c 25 c 45 c 85 c 65 c 105 ? 55 c 0.01 0.1 1 10 10 100 1,000 10,000 100,000 1,000,000 ratio to 25 c, 120 hz value ? 40 c 0 c 25 c 65 c 85 c 45 c ? 20 c 105 c ? 55 c impedance vs. temperature and frequency esr vs. temperature and frequency capacitance vs. temperature & frequency 470 f @ 80 vdc (18 x 16.5 mm) 470 f @ 80 vdc (18 x 16.5 mm) 470 f @ 80 vdc (18 x 16.5 mm) -2 0 -1 5 -1 0 -5 0 5 10 15 -60 -10 40 90 140 capacitance change (%) 47 f @ 6.3 vdc (4 x 5.8 mm) 100 f @ 6.3 vdc (6.3 x 5.8 mm) 1000 f @ 6.3 vdc (8 x 10.2 mm) 33 f @ 8 0 vdc (8 x 1 0 .2 m m ) capacitance change vs.temperature temperature ( c) dissipation factor vs.temperature frequency (hz) frequency (hz) frequency (hz) temperature ( c) capacitance change vs. time time (hours) (typical performance afk series @ 120 hz) (typical performance afk series @ 120 hz) (typical performance for afk series)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com avs, aha, afc, afk, ahd, aeb tape and reel specifications tape specifications a 0.2 p1 b 0.2 w 0.3 4 0.1 1.5 dia 1.75 0.1 f 0.1 0.4 t 0.2 component orientation polarity stripe (-) cathode case code w a b p1 f t a 12.0 3.4 3.5 8.0 5.5 5.8 b 12.0 4.7 4.6 8.0 5.5 5.8 c 12.0 6.0 6.0 12.0 5.5 5.8 d 16.0 7.0 7.0 12.0 7.5 5.8 x 16.0 7.0 7.0 12.0 7.5 8.4 e 16.0 8.7 8.7 12.0 7.5 6.8 f 24.0 8.7 8.7 16.0 11.5 11.0 g 24.0 10.7 10.7 16.0 11.5 11.0 case codewabcdfps j 32.0 10.7 10.7 14.5 14.5 14.2 20.0 28.4 k 32.0 10.7 10.7 14.5 18.5 14.2 20.0 28.4 h 32.0 14.0 14.0 18.0 14.5 14.2 24.0 28.4 l 32.0 14.0 14.0 18.0 17.5 14.2 24.0 28.4 p 44.0 17.5 17.5 23.0 17.5 20.2 28.0 40.4 r 44.0 19.5 19.5 26.0 17.5 20.2 32.0 40.4 s 44.0 19.5 19.5 26.0 22.5 20.2 32.0 40.4 u 44 17.5 17.5 23 22.5 20.2 28 40.4 0.2+0.05 0.75+0.1 2.00.1 4.00.1 ? 1.50.1 p0.1 b0.5 w0.3 s0.1 f0.1 1.750.1 a0.5 d0.2 0.5 c0.5 (mm) (mm)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com avs, aha, afc, afk, ahd, aeb tape and reel specifications land pattern: reel specifications w case code a b c d e w t a, b size 3802 50 min 13.00.5 21.00.8 2.00.5 141 3.0 c, d, e, x size 3802 50 min 13.00.5 21.00.8 2.00.5 181 3.0 f, g size 3802 50 min 13.00.5 21.00.8 2.00.5 261 3.0 j, k, h, l size 3302 50 min 13.00.5 21.00.8 2.00.5 341 3.0 p, r, s, u size 3302 50 min 13.00.5 21.00.8 2.00.5 461 3.0 e c d r: 1.0 mm (.039 in.) a t b case codeabc a 0.6 2.2 1.5 b 1.0 2.5 1.6 c 1.5 2.8 1.6 d 2.2 3.0 1.6 e 2.2 4.5 1.6 f 3.2 4.0 2.0 g 4.6 4.3 2.0 j, k 4 4.5 2.0 h 4.0 5.7 2.0 l 4.0 5.7 2.0 p 6.0 6.5 2.5 r, u 6.0 6.5 2.5 s 6.0 7.5 2.5 1234567890123456789 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1234567890123456789 1234567890123456789 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1 23456789012345678 9 1234567890123456789 c b b a (mm) (mm)
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com avs, aha, afc, afk, ahd, aeb reflow solder & case dimensions outline drawing case dimensions reflow soldering temperature profile: (mm) *5.8 +0.1,-0.2 for afk and ahd series case peak max. time code temp ( c) @ 200 c (sec.) a, b, c, d, x 240 40 e, f, g, h 230 30 j, k, l, p r, s, u case code d 0.5 l a 0.2 h (max) i (ref) w p (ref) k a 3.0 5.4 +.1,-.2 3.3 4.5 1.5 0.55 0.1 0.6 0.35 + 0.15/-0.20 b 4.0 5.4 +.1,-.2 4.3 5.5 1.8 0.65 0.1 1.0 0.35 + 0.15/-0.20 c 5.0 5.4 +.1,-.2 5.3 6.5 2.2 0.65 0.1 1.5 0.35 + 0.15/-0.20 d 6.3 5.4 +.1,-.2 6.6 7.8 2.4 0.65 0.1 1.8 0.35 + 0.15/-0.20 x 6.3 7.9 .3 6.6 7.8 2.6 0.65 0.1 1.8 0.35 + 0.15/-0.20 e 8.0 6.2 .3 8.3 9.5 3.4 0.65 0.1 2.2 0.35 + 0.15/-0.20 f 8.0 10.2 .3 8.3 10 3.4 0.90 0.2 3.2 0.70 0.20 g 10.0 10.2 .3 10.3 12 3.5 0.90 0.2 4.6 0.70 0.20 h 12.5 13.5 .5 13.5 15 4.7 0.9 0.3 4.4 0.70 0.30 j 10 13.5 10.3 12 3.5 0.9 0.2 4.6 0.70 0.20 k 10 17.5 10.3 12 3.5 0.9 0.2 4.6 0.70 0.20 l 12.5 16.5 .5 13.5 15.0 4.7 0.90.3 4.4 0.70 0.30 p 16.0 16.5 .5 17.0 19.0 5.5 1.20.3 6.7 0.70 0.30 r 18.0 16.5 .5 19.0 21.0 6.5 1.20.3 6.7 0.70 0.30 s 18.0 21.5 .5 19.0 21.0 6.5 1.20.3 6.7 0.70 0.30 u 16.0 21.5 17.0 19.0 6.7 1.20.3 6.7 0.70 0.30 120 seconds preheat maximum time @ 200 c (see chart right) time 160 c 200 c peak temp. (see chart right) 5 seconds maximum h l w p d 0.3 mm max. a i i k
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com v-chip cleaning and coating guide below is a table discribing the usable solvents for cleaning a pc board containing v-chips. recommended symtoms solvent type name manufacturer use level of damage water distilled water 1 none alkaline aqua cleaner 210sep sanei 2 pine alpha st-100s aralaw a kasei kogyo 2 clean-thru 750h 2 surface active clean-thru 750l kao corporation 2 agent clean-thru 710m 2 sun-elec b-12 sanyo kasei 2 dk be-clean cw-5790 dai-ichi kogyo seiyaku 2 petroleum cold-cleaner p3-375 henkel hakusui 3 based techno-cleaner 219 seiwa sangyo 3 hydrocarbon axarel 32 mitsui dfc 3 alcohol base isopropyl alcohol 1 none techno-care frw-17 3 silicon base techno-care frw-17 toshiba corporation 3 (techno-care frv-100) 3 halogenated asashi-clean ak-225aes ashahi glass 3 hydrocarbon hcfc141b-ms dalkin kogyo 3 telpen base telpen-cleaner ec-7r nippon alpha metals 3 swelled seal contains cfc's subject to environmental regulations water base solvent base none, though marking ink may fade swellling on sealing rubber rinse and dry well after cleaning none if used in combination use level number 1 cleaning is possible 2 cleaning is possible (markings may fade) 3 cleaning is possible (use caution. 1 and 2 are better choices) recommendation do not use chlorine-based halogenated cleaning solvents, adhesives or coating agents. when halogenated chlorine-based solvents are used in the cleaning process, free clorine is liberated from the solvent. this chlorine causes corrosion and deterioration of the aluminum inside the capacitor dangers of ?free-chlorine?: after the solvent dries, the chlorine remains on the capacitor seal, the chlorine slowly permeates into the capacitor element causing corrosion and damage that happens slowly. it may take some time before a failure is apparent. a representation of the chemical reaction is on the following page. table 1 cleaning v-chips may be immersed for 5 minutes, safely, in level 1&2 solvents. use level 3 solvents with caution.
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com reaction of free-chlorine and aluminum combined free chlorine and hydrogen become hydrochloric acid, but it has high dissociation and most of it becomes chlorine ions. these chlorine ions react with the aluminum. the order of the reactions is represented below. 1.) hydration of oxide film alo 3 + 3h 2 o > 2al(oh) 3 2.) reaction of hydrated oxide film and chlorine (dissolution of film) al(oh) 3 + 3hcl > alcl 3 + 3h 2 o 3.) reaction of aluminum and hydrochloric acid (dissolution of aluminum) al + 3hcl > alcl 3 + 3/2h 2 4.) precipitation of aluminum hydroxide alcl 3 + 3h 2 o > al(oh) 3 + 3hcl the entire reaction can be summerized as the following: al + al 2 o 3 + 3hcl 3 + 3h 2 o > 2al(oh) 3 + alcl 3 + alcl 3 + h3/2 therefore the compounds produced by the reactions are aluminum hydroxide and hydrochloric acid from reaction #4; the hydrochloric acid is not consumed and acts as a catalyst. cl cl cl c c h h h hcl cl cl c c h h hh + cl cl cc h h + hcl = chlorosen cl cl cc h h h cl + (2h) electrolysis reaction dichloroethane dicloroethylene fig. 1 decomposed reaction of cleaning solvents (free-chlorine) free-chlorine diagram: v-chip cleaning and coating guide
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com composition boiling point ( c) common name 1.1.1-trichloroethane 74.1 chlorosen trichloroethylene 87.2 trichlene tetrachloroethylene 121.1 perchloroethylene solvents that should not be used table 2 additional cleaning notes: 1.) solvents containing cfc?s destroy the ozone layer and should be avoided to protect the global environment. 2.) to avoid solvent residue between the capacitor?s seal and the pc board, make sure the assembly is dried thoroughly immediately after cleaning. v-chip cleaning and coating guide coating table 3 below is a list of coatings that are safe for use with v-chips manufacturer material coating material name acrylic taffi-1141, taffi-1147 urethane taffi-1154 acrylic humi seal 1b66 urethane humi seal 1a27 dow corning silicon perugan z, perugan c nihon zeon urethane quinate system 160b hitachi chemical boxy brown influence of coating materials coating materials are typically used for insulation, waterproofing, dustproofing and rustproofing. when coating materials are selected there are factors to prevent internal corrosion (chlorine reaction with aluminum) while the capacitor is functioning. the following steps will help prevent this damage to the capacitor. a.) corrosion reaction avoid halogen solvents which permeate the capacitor ? s seal, releasing chlorine which reacts with the aluminum inside the capacitor. b.) selecting a coating material it is necessary to select a coating material that contains no chlorine. the coating consists of the main ingredient which could be urethane resin, acrylic resin or other polymer, a solvent and other additives such as flameproofing agents.
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax(508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com v-chip cleaning and coating guide the coating ? s solvent dries and diffuses into the rubber seal of the capacitor, therefore halogenated hydrocarbon solvents containing chloride should not be used. similar to the solvent, additives can permeate into the capacitor through the rubber seal. ingredients in many additives might not be listed, therefore use caution when choosing an additive. c.) other concerns solvents and additives are subject to change without notice. make sure ingredients are identified. avoid coating a substrate after cleaning it with a halogenated hydrocarbon. the coating will prevent the remaining solvent from diffusing which may cause corrosion.

▲Up To Search▲

Price & Availability of AFK475M50B12T

	To Download AFK475M50B12T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .